Page 16 Ignition checker nents. Push the starter tank to carburetor and also filters the The engine stop switch "1" is located down lightly with your foot until the fuel.
Drain the break-in oil-fuel mixture Never mix two types of oil in the 5. The engine is warmed up when it from the fuel tank and refill with same batch; Page Tightening Torques 0. Torque specifications 6 mm for special components or assem- blies are included in the applicable sections of this book.
Pass the clutch cable in front of the center of the cylinder head tightening nut. Pass the air vent hose, overflow hose and crankcase breather hose between the frame and connecting rod.
Then pass the radiator breather hose inside the CDI magneto lead. High tension cord bracket. Pass the radiator breather hose CDI unit band Pass the high tension cord to the behind the radiator hose. Page Maintenance Intervals The following schedule is intended as a general guide to maintenance and lubrication. Bear in mind that such factors as weather, terrain, geographical location, and individual usage will alter the required maintenance and lubrication intervals.
If you are a doubt as to what intervals to follow in maintaining and lubricating your machine, consult your Yamaha dealer. Lubricate, slack, alignment Chain slack: 48—58 mm 1. Before using this machine, check the following points. Thoroughly wash your eye with Do not remove the radiator cap water and see your doctor.
Apply the specified pressure. Check: 1. Inspect: 2. Turn out the pilot air screw by the factory-set number of turns. Start the engine and warm it up for several minutes and wait for To optimize the fuel flow at a smaller five minute.
Pull the lever in or push down on Brake lever position adjustment ment, make sure that the rear the pedal. Hold the lever or pedal steps: brake does not drag. Loosen the locknut "1". Loosen the bleed screw and allow b. Remove the pad pin and brake pads "4". Install the pad pin plug "10". Loosen the pad pin "3". Remove the rear wheel "4" and Pad pin plug: e. Connect the transparent hose "5" brake caliper "5". PADS" section. Check: eral times to find the tightest point. Tighten the locknuts.
Always adjust each front fork to 2. Remove the air bleed screw "1" the same setting. Uneven adjust- and release the internal pressure ment can cause poor handling and from the front fork. Adjust: ing bearings. Install the washer "5", upper bracket "6", washer "7", steering stem nut "8", handlebar "9", han- Steering ring nut adjustment dlebar upper holder "10" and steps: number plate "11". Remove the number plate. Lubricate the following areas Loosen the screws stator "1". Those who have little knowledge and skill concerning servicing are request- ed not to undertake inspection, adjustment, disassembly, or reassembly only by reference to this manual.
Yamaha bond No. Blow out all passages and position sensor "1" except when jets with compressed air. Measure: chamfered side "a" to the right. Install: Insert the set pin "3" included in own- er's tool kit to remove the bolt push rod.
Check: 6. Bolt brake pedal Shift the brake pedal downward. Lock washer Refer to removal section. Straighten the lock washer tab and Clutch spring free use the clutch holding tool "4" Place an aluminum plate "a" between the teeth of the primary drive gear "2" and driven gear "3". Governor assembly Dowel pin Refer to removal section.
Install: 1. Remove: 1. Install: Ignition timing B. Bolt brake pedal : 26 Nm 2. SHAFT" section. Main axle Refer to removal section. Remove: the sliding gear, then install.
Nut rear wheel axle Rear wheel axle Drive chain puller Rear wheel Refer to removal section. Apply the lithium soap base grease on the oil seal lip.
Drain the brake fluid. Refer to removal section. Brake hose holder protector Union bolt Brake hose Brake caliper piston dust seal Refer to removal section. Brake caliper piston seal Refer to removal section. Washer Push rod Rear Brake master cylinder kit Install: 2. Click here to download your YZRY owners manual. Click here to download your YZ A owners manual.
Click here to download your YZ AA1 owners manual. Click here to download your YZ B owners manual. Click here to download your YZ FB owners manual. This is an awesome site, very helpful.
Would it be possible for you to let me know the password needed to edit the files so that I can remove the non-English pages? Thanks for all the available books I wanted to know if it was available manual Yamaha YZ Thank you. My yz 2 stroke does only take ml then the oli comes out the oli level bolt Is this normal or not. Your email address will not be published. Skip to content About. Thanks, Jim. Pingback: Does it get rusted whenever you take it to the car wash?
Im looking for manual for YZ Can you upload it here? I have a yamaha yz What oil does it use and how much? Leave a Reply Cancel reply Your email address will not be published. Next Next post: Suzuki Owners Manuals.
0コメント