Page Block Diagram Block Diagram There is no need to run Setup when starting the computer unless you get a Run Setup message. When the message of press the key of [Delete] to enter the setup menu. Page Product Information Product Information The screen below appears if you select Product Information from the main menu: The Product Information menu contains general data about the system, such as the product name, serial number, BIOS version, etc.
This information is necessary for troubleshooting maybe required when asking for technical support. Page 33 The following table describes the parameters found in this menu. If this function is enabled and there is someone attempts to write data to this area, BIOS will show a warning message on screen and the alarm will beep. Enabling pulse spectrum spread modulation changes the extreme values from spikes to flat curves, thus reducing EMI.
This benefit may in some case be outweighed by problems with timing-critical devices, such as a clock-sensitive SCSI device.
Page Integrated Peripherals Integrated Peripherals The following table describes the parameters found in this menu. Page 41 The following table describes the parameters found in this menu. Page 43 The following table describes the parameters found in this menu.
Page 45 The following table describes the parameters found in this menu. If you install an add-in FDC or the system has no floppy drive, select Disabled in this field. Page Power Management Power Management The Power Management menu lets you configure your system to most effectively save energy while operating in a manner consistent with your own style of computer use. The following screen shows the Power Management parameters and their default settings Page 47 The following table describes the parameters found in this menu.
Page 50 The following table describes the parameters found in this menu. Thus the AGP display becomes the primary display. Reset Normally, you leave this field Disabled.
Page Chapter 3 Machine Disassembly And Replacement Machine Disassembly and Replacement To disassemble the computer, you need the following tools: Wrist grounding strap and conductive mat for preventing electrostatic discharge. Wire cutter. Phillips screwdriver may require different size. NOTE: The screws for the different components vary in size. During the disassembly process, group the screws with the corresponding components to avoid mismatches when putting back the components.
Page General Information General Information Before You Begin Before proceeding with the disassembly procedure, make sure that you do the following: 1. Turn off the power to the system and all peripherals.
Unplug the AC adapter and all power and signal cables from the system Page Disassembly Procedure Disassembly Procedure This section tells you how to disassemble the system when you need to perform system service. Please also refer to the disassembly video, if available. Place the system unit on a flat, steady surface. Release the screw that shown below. Remove the top cover.
Page 63 4. As shown pull three button up. Take the belt shown as below. Release this screw first 6. Detach HDD date and power cable.
Page 64 8. Detach LED cable. Release four screws as shown below and disconnect the CPU cools. Page 65 Disconnect the CPU. Remove the Memory. Remove the Video-in cable and TV-out cable.
Table Of Contents. Table of Contents. Previous Page. Next Page. Other companies' product names or trademarks are used herein for identification purposes only and belong to their respective companies. Page 3: Safety Instructions Information for your safety and comfort Safety instructions Read these instructions carefully. Keep this document for future reference. Follow all warnings and instructions marked on the product. Turning the product off before cleaning Unplug this product from the wall outlet before cleaning.
Do not use liquid cleaners or aerosol cleaners. Page 4 do not place the product on a vibrating surface. Page 6: Disposal Instructions To minimize pollution and ensure utmost protection of the global environment, please recycle. Page 7: Finding Your Comfort Zone Finding your comfort zone Find your comfort zone by adjusting the viewing angle of the monitor, using a footrest, or raising your sitting height to achieve maximum comfort.
Page 9: Table Of Contents Information for your safety and comfort iii Safety instructions Additional safety information Disposal instructions Tips and information for comfortable use System tour Front panel Rear panel Setting up your computer Necessary to know before setup Selecting a location Opening the package Connecting peripherals Starting your computer Shutting down your computer Page 10 Declaration of Conformity Remark: All images are for reference purposes only.
Actual configuration may vary. The computer uses a state-of-the-art bus architecture, which improves system efficiency and helps the system support varied multimedia and software applications. Connecting peripherals After everything is connected, plug the power cord into the system and insert the other end into a power outlet.
Before you choose new components, please ask your authorized Acer dealer whether the part will operate within your AcerSystem system. In order to ensure proper setup and installation, please refer to the instructions provided with your new components. Page Frequently Asked Questions Frequently asked questions The following questions are possible situations that may arise during the use of your computer and each is followed by easy answers and solutions to the situation. Q: I pressed the power switch but the system did not boot up.
A: Check the LED located above the power switch. Following these instructions will help you maximize the durability of your computer. Do not place it near sources of heat, such as a radiator.
0コメント